您现在的位置:首页 » 新闻资讯 » 投影机维修资料 » 常用投影机232代码 济南三虎快易修 投影机维修

常用投影机232代码 济南三虎快易修 投影机维修

2015-05-04 19:28:37 点击数:
关键字: 常用投影机232代码 济南三虎快易修 投影机维修

关于串口控制投影机的操作方法的几个步骤 
1、将中控接上电源,连好控制面板 
2、将中控主机串口(RS232)接口与电脑主机COM口连接好 
3、将中控系统随机的光盘放入电脑中,打开“串口写码程序”软件 
4、写码程序设置处理: 
A:选择电脑的COM口,注意该端口不能被占用掉,否则无法与中控通讯 
B:选择输入码格式,16进制还是ASCII码 
C:选择波特率 
D:点击“电源开”键,并清空输入窗,按照投影机灯泡“电源开”的标准串口码输入到窗口中,并点击“确认”键后再点击“发送”键,此时应在控制面板上听到“嘟”—“嘟”两声接收蜂鸣,表示该码发送并成功接收到中控芯片中。 
E:依次将“电源关”、“计算机”、“视频”键的串口码输入到中控中。 
F:将中控主机控制投影机端口选择“串口控制”接口,并将控制接插头插入,在投影机机身上“computer”控制口或称“RS232”控制接口上找到正确的接线端,一般投影机控制脚被明确表示出来,如三洋投影机,NEC,等为8针圆脚(4脚接地,1脚接收等)。爱普生是标准九针口 (2脚接受,5脚接地)     .......... 
市场上现流行的RS232接口有两种:一种是标准9针接口,另一种是圆孔8针接口。
 串口写入程序文件夹里文件的说明:
 1、串口写码程序为单机的中控写码程序,此程序不可导入和导出串口码
 2、串口写码程序_通用为通用的写码程序。
   A:根据选择可对单机的中控和网络中控进行写串口码,程序中里有个机器类别选择即为此功能,现此中控为单机的中控;
   B:在原来的基础上增加了串口码文件可导入和串口码可导出到文件的功能。在没有串口码文件时,
    先将串口码输入到投影机代码输入窗中,接着按导出代码,然后将其取一文件名保存好,依次将投影机
    的所有串口码导出并保存,有了串口码文件后,将程序左边所有的设置设好,接着点导入代码按钮,
    选择相应的串口代码文件后,出现一对话窗“导入结束,按“发送”开始”,此时点“OK”,再点
    发送即可,发送串口码时,会有声音提示,到最近一声响时串口代码就发送好了。
 3、COM测试为串口代码的测试软件
 4、投影机串口码为有关的一些投影机串口代码,可供参考
 5、关于串口控制投影机的操作方法的几个步骤为串口代码写入的一些注意事项,请仔细阅读
 MIMITSUBI 
(三菱) 
S50U S200U

9600bps

DIN-8P 
RD:1 
TD:7 
GND:4

开机:30H,30H,21H,0DH 
关机:30H,30H,22H,0DH 
VGA1:30H,30H,5FH,72H,31H,0DH 
视频:30H,30H,5FH,76H,31H,0DH

SHAPR C30 
(夏普) 
DB9: 
RD:2 
GND:5 
TD:3 
9600bps

开机:50H,4FH,57H,52H,20H,20H,20H,31H,0DH 
关机:50H,4FH,57H,52H,20H,20H,20H,30H,0DH 
VGA1:49H,52H,47H,42H,20H,20H,20H,31H,0DH 
视频:49H,56H,3BH,44H,20H,20H,20H,31H,0DH
 普乐士(PLUS) 
U2 850W 
19200 bps 
开机: BEH,EFH,02H,06H,00H,79H,C0H,E0H,00H,00H,00H,00H,00H 
关机:BEH,EFH,02H,06H,00H,A8H,C1H,E1H,00H,00H,00H,00H,00H 
VGA1:BEH,EFH,02H,06H,00H,0DH,C4H,D4H,00H,00H,00H,00H,00H 
视频:BEH,EFH,02H,06H,00H,DCH,C5H,D5H,00H,00H,00H,00H,00H 
明  基 
(X550) 
DIN-8P 
RD:7 
TD:3 
GND:外壳 
19200 bps 
开机: BEH,EFH,02H,04H,00H,57H,48H,01H,00H,01H,00H 
关机:BEH,EFH,02H,04H,00H,A7H,48H,01H,00H,02H,00H 
VGA1:BEH,EFH,03H,06H,00H,40H,D2H,01H,00H,07H,00H,00H,00H 
视频:BEH,EFH,03H,06H,00H,D0H,D3H,01H,00H,07H,00H,01H,00H 
S-视频:BEH,EFH,03H,06H,00H,20H,D3H,01H,00H,07H,00H,02H,00H
 品牌 型号 串口码
 飞利普DB9:RD:2TD:3GND:5 1241PXG20波特率:9600 开机:POWR(3空格)1(回车)关机:POWR(3空格)0(回车)视频:IVED (3空格)1(回车)VGA1:IRGB(3空格)1(回车)VGA2:IRGB(3空格)2(回车)
 NECDIN-8PRD:1GND:4TD:7 440 波特率38400VT650波特率:19200 开机:02H,00H,00H,00H,00H,02H关机:02H,01H,00H,00H,00H,03HRGB:02H,03H,00H,00H,02H,01H,01H,09H视频:02H,03H,00H,00H,02H,01H,06H,0EHS-视频:02H,03H,00H,00H,02H,01H,0BH,13H
 EPSONDB9:RD:2GND:5TD:35600和7700的投影机的6脚要接高电平 810/600/800/820波特率:9600 开机:PWR(空格)ON(回车)关机:PWR(空格)OFF(回车)RGB1(ANALOG):SOURCE(空格)11(回车)RGB1(DIGITAL):SOURCE(空格)12(回车)RGB1(RGB-VIDEO):SOURCE(空格)13(回车)RGB2(ANALOG):SOURCE(空格)21(回车)RGB2(RGB-VIDEO):SOURCE(空格)22(回车)RGB2(YCBCR): SOURCE(空格)23(回车)RGB2(YPBPR): SOURCE(空格)24(回车)视1:SOURCE(空格)41(回车)S视:SOURCE(空格)42(回车)
 5600/7600/5300/7350/7250 开机:1BH,07H,01H,00H,03H,01H,F4H关机:1BH,07H,01H,00H,03H,00H,F5HVGA1:1BH,07H,01H,01H,00H,10H,EFHVGA2:1BH,07H,01H,01H,00H,11H,E8HS-VIDEO:1BH,07H,01H,01H,00H,22H,D7HVIDEO:1BH,07H,01H,01H,00H,21H,D7H
 7700 开机:0x1d,0x00,0x09,0x01,0x01,0x00,0x03,0x01,0xf1关机:0x1d,0x00,0x09,0x01,0x01,0x00,0x03,0x00,0xf2视频:0x1d,0x00,0x09,0x01,0x01,0x01,0x00,0x21,0xd3S:       0x1d,0x00,0x09,0x01,0x01,0x01,0x00,0x22,0xd2VAG1: 0x1d,0x00,0x09,0x01,0x01,0x01,0x00,0x10,0Xe4BNC_RGB: 0x1d,0x00,0x09,0x01,0x01,0x01,0x00,0x30,0xc4BNC_YcrCb: 0x1d,0x00,0x09,0x01,0x01,0x01,0x00,0x40,0xb4DVI: 0x1d,0x00,0x09,0x01,0x01,0x01,0x00,0x50,0xa4
 8000波特率:9600 开机:PWR;1(回车)关机:PWR;0(回车)VGA1:SRC;0(回车)视频:SRC;2(回车)
 3M
 8775/8675波特率:19200
 开机:BEH,EFH,03H,06H,00H,2AH,D3H,01H,00H,00H,60H,00H,00H
 关机:BEH,EFH,03H,06H,00H,BAH,D2H,01H,00H, 00H,60H,01H,00HRGB1:BEH,EFH,03H,06H,00H,FEH,D2H,01H,00H,00H,20H,00H,00H
 RGB2:BEH,EFH,03H,06H,00H,3EH,D0H,01H,00H, 00H,20H,04H,00H
 视频:BEH,EFH,03H,06H,00H,6EH,D3H,01H,00H,00H,20H,01H,00H
 S-VIDEO:BEH,EFH,03H,06H,00H,9EH,D3H,01H,00H,00H,20H,02H,00H
 DVI:BEH,EFH,03H,06H,00H,0EH,D2H,01H,00H,00H,20H,03H,00H
 
松下
 松下
 开机:02H,PON,03H
 关机:02H,POF,03H
 视频:02H,IIS,“:”,VID,03H
 S视频:02H,IIS,“:”,SVD,03H
 RGB1:02H,IIS,“:”,RG1,03H
 RGB2:02H,IIS,“:”,RG2,03H
 
东芝
 DIN-8 PRD
 串口码有两种形式,一种是ASCII码,另一种是16进制码。16进制码的每个数据之间要用空格分开。ASCII码原样输入有空格的要空格,和回车的要回车,如果是回车在码尾的就不用回车直接将“码尾加回车”选项选上。
          投影机串口的接口一般有3种形式,一是9针的标准接口,一个是8针的圆接口,另一个是15针的标准接口。9针的接口一般为:2脚为信号接收端(其中松下的投影机是3脚为信号接收端),5脚为地。8针的圆接口一般为:1脚为信号接收端,4脚为地,其中明基的是7脚为信号接收端,外壳为地。15针的接口为:13脚为信号接收端,10脚为地。
 富士通:
 波特率:19200,ASCII码,码尾加回车
 开机:IP@G回车IPRM01回车IP@Q回车
 关机:IP@G回车IPRM02回车IP@Q回车
 RGB1:IP@G回车IPRM03回车IP@Q回车
 VIDEO:IP@G回车IPRM05回车IP@Q回车
 爱其:
 波特率:19200,ASCII码,码尾加回车
 开机:C00回车
 关机:C01回车
 视频:C06回车
 计算机:C05回车
 上:C3C回车
 下:C3D回车
 左:C3B回车
 右:C3A回车
 大:C30回车
 小:C31回车
 明基:
 波特率:19200,十六进制
 POWER:BE EF 02 06 00 13 CE AA 00 00 00 00 00
 INPUT SELECT:BE EF 02 06 00 C4 C8 8D 00 00 00 00 00
 ZOOM+:BE EF 02 06 00 AD CD B4 00 00 00 00 00
 ZOOM-:BE EF 02 06 00 7C CC B5 00 00 00 00 00
 东芝
 DIN-8 PRD:1 TD:7 GND:4
 开机:02H,PON,03H
 关机:02H,POF,03H     (有确认信息)
 关机:02H,PSD,03H     (没有确认信息)
 VGA1:02H,IN1,03HVGA2:02H,IN2,03H
 视频:02H,IN3,03HS-VIDEO:02H,IN4,03H
 CAMERA:02H,IN6,03H
 NEC
 DIN-8P
 RD:1
 GND:4
 TD:7
 440 
波特率38400
 VT650
 波特率:19200
 LT220+/240+/260+ 
波特率
 38400或9600
 MT860/1060/1065
 波特率:38400 
开机:02H     00H     00H     00H     00H     02H
 关机:02H     01H     00H 00H 00H 03H
 RGB:02H 03H 00H 00H 02H 01H 01H 09H
 视频:02H 03H 00H 00H 02H 01H 06H 0EH
 S-视频:02H 03H 00H 00H 02H 01H 0BH 13H
 NEC LT220这型投影机开机要发两次码,一次待机一次开启
 EPSON
 DB9:
 RD:2
 GND:5
 TD:3
 5600和7700的投影机的6脚要接高电平
 波特率:9600
 810/600/800/820/73/53
 波特率:9600 
开机:PWR(空格)ON(回车)
 关机:PWR(空格)OFF(回车)
 RGB1(计算机1)(ANALOG):SOURCE(空格)11(回车)  
 RGB1(DIGITAL):SOURCE(空格)12(回车)
 RGB1(RGB-VIDEO):SOURCE(空格)13(回车)
 RGB2(计算机2)(ANALOG):SOURCE(空格)21(回车)
 RGB2(RGB-VIDEO):SOURCE(空格)22(回车)
 RGB2(YCBCR): SOURCE(空格)23(回车)
 RGB2(YPBPR): SOURCE(空格)24(回车)
 视1:SOURCE(空格)41(回车)
 S视:SOURCE(空格)42(回车)
 5600/7600/
 5300/7350/
 7250
 开机:1BH 07H 01H 00H 03H 01H F4H
 关机:1BH 07H 01H 00H 03H 00H F5H
 VGA1:1BH 07H 01H 01H 00H 10H EFH
 VGA2:1BH 07H 01H 01H 00H 11H E8H
 S-VIDEO:1BH 07H 01H 01H 00H 22H D7H
 VIDEO:1BH 07H 01H 01H 00H 21H D7H
 7700 开机:1dH 00H 09H 01H 01H 00H 03H 01H f1H
 关机:1dH 00H 09H 01H 01H 00H 03H 00H f2H
 视频:1dh 00H 09H 01H 01H 01H 00H 21H d3H
 S视频:1dh 00H     09H     01H 01H 01H 00H 22H d2H
 VAG1: 1dH 00H 09H 01H 01H 01H 00H 10H e4H
 BNC_RGB: 1dh 00H 09H 01H 01H 01H 00H 30H c4H
 BNC_YcrCb:
 1dH 00H 09H 01H 01H 01H 00H 40H b4H
 DVI: 1dH 00H 09H 01H 01H 01H 00H 50H a4H
 宝施马 8000
 波特率:
 9600 
开机:PWR;1(回车)
 关机:PWR;0(回车)
 VGA1:SRC;0(回车)
 视频:SRC;2(回车)
 PROXIMA
 DIN-8P
 RD:6
 TD:4
 GND:8
 波特率:
 9600 5150/5155/
 6150/6155/
 6100 
日立
 DB15
 公头
 RD:13
 TD:14
 GND:10 TECHNICAL
 波特率:
 19200
 开机:BEH EFH 03H 06H 00H BAH D2H 01H 00H                00H 60H 01H 00H
 关机:BEH EFH 03H 06H 00H 2AH D3H 01H 00H           &nb
 开机:A9H 17H 2EH 00H 00H 00H 3FH 9AH
 关机:A9H 17H 2FH 00H 00H 00H 3FH 9AH
 VGA1:A9H 17H 2BH 00H 00H 00H 3FH 9AH
 VGA2:A9H 17H 2CH 00H 00H 00H 3FH 9AH
 视频:A9H 17H 2AH 00H 00H 00H 3FH 9AH
 MIMITSUBI
 (三菱)
 S50U S200U
 9600bps
 DIN-8P
 RD:1
 TD:7
 GND:4 
开机:30H 30H 21H 0DH
 关机:30H 30H 22H 0DH
 VGA1:30H 30H 5FH 72H 31H 0DH
 视频:30H 30H 5FH 76H 31H 0DH
 SHAPR 
DB9:
 RD:2
 GND:5
 TD:3 
C30
 (夏普)
 9600bps 
开机:50, H 4FH 57H 52H 20H 20H 20H 31H 0DH
 关机:50H 4FH 57H 52H 20H 20H 20H 30H 0DH
 VGA1:49H 52H 47H 42H 20H 20H 20H 31H 0DH
 视频:49H 56H 3BH 44H 20H 20H 20H 31H 0DH
 普乐士(PLUS)
 U2 850W
 19200 bps 
开机: BEH EFH 02H 06H 00H 79H C0H E0H 00H 00H 00H 00H 00H
 关机:BEH EFH 02H 06H 00H A8H C1H E1H 00H 00H 00H 00H 00H
 VGA1:
 BEH EFH 02H 06H 00H 0DH C4H D4H 00H 00H 00H 00H 00H
 视频:
 BEH EFH 02H 06H 00H DCH C5H D5H 00H 00H 00H 00H 00H
 明  基
 (X550)
 DIN-8P
 RD:7
 TD:3
 GND:外壳 19200 bps 
开机: BEH EFH 02H 04H 00H 57H 48H 01H 00H 01H 00H
 关机:BEH EFH 02H 04H 00H A7H 48H 01H 00H 02H 00H
 VGA1:
 BEH EFH 03H 06H 00H 40H D2H 01H 00H 07H 00H 00H 00H
 视频:BEH EFH 03H 06H 00H D0H D3H 01H 00H 07H 00H 01H 00H
 S-视频:
 BEH EFH 03H 06H 00H 20H D3H 01H 00H 07H 00H 02H 00H
 明  基
 (DX655)
 DIN-8P
 RD:7
 TD:3
 GND:外壳
 LG
 RT-JT40
 DB9: 19200 bps 开机:
 BEH EFH 02H 06H 00H 13H CEH AAH 00H 00H 00H 00H 00H
 关机:
 BEH EFH 02H 06H 00H 13H CEH AAH 00H 00H 00H 00H 00H
 VGA1:
 BEH EFH 02H 06H 00H C4H C8H 8DH 00H 00H 00H 00H 00H
 视频:
 BEH EFH 02H 06H 00H C4H C8H 8DH 00H 00H 00H 00H 00H
 S-视频:
 BEH EFH 02H 06H 00H C4H C8H 8DH 00H 00H 00H 00H 00H
 OPTOMA
 奥图码
 DIN-3P
 RD:3
 TD:1
 GND:2
 从左向右看 EP-756  
 9600 bps 
开机:OKOKOKOKOK(回车)
 关机:*(空格)0(空格)IR(空格)002(回车)
 RGB1:     *(空格)0(空格)IR(空格)015(回车)
 VIDEO: *(空格)0(空格)IR(空格)019(回车)
 ASK
 ASK
 DIN-8 PRD:6 TD:4  GND:8
 C90/C100 波特率:9600
 开机:BEH,EFH,80H,06H,00H,00H,00H,01H,00H,01H,00H,00H,00H关机:BEH,EFH,80H,06H,00H,00H,00H,01H,00H,00H,00H,00H,00H
 VGA1:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 00H,00H
 DVI1:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 01H,00H
 S1:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 02H,00H
 V1:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 03H,00H
 VGA2:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 04H,00H
 DVI2:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 05H,00H
 S2:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 06H,00H
 V2:BEH,EFH,80H,06H,00H,00H,00H,01H,00H ,32H, 00H, 07H,00H

留言咨询
提交留言 (* 为必填项目)
* 姓名
* 内容

山东投影机维修|济南投影仪维修|投影仪灯泡|投影机配件|投影仪安装|济南三虎快易修服务站 [三虎科技] 版权所有 2002-2013 All Rights Reserved Powered by SANHU V5
在线客服
  • 投影机维修咨询
    点击这里给我发消息